Office Monitor

Patrick is away from his Desk A0>1000
Office Lights are detected as being on A5>200
Current humdity is 33.0%
Current temperature is 69.0F

Debug:
analog input 0 is 36
analog input 1 is 150
analog input 2 is 224
analog input 3 is 259
analog input 4 is 300
analog input 5 is 185
1 minute auto refresh
Arduino POE Ethernet
Simplytronics Wide Angle PIR
Parallax 4x30 LCD
KY015 DHT11 Temperature and humidity sensor

Live: http://96.88.231.122
Source Code: https://github.com/insidenothing/arduino/blob/master/POEserver/POEserver.ino

anyBBS Dialup to Telnet Launcher v0.1

/bbs/getty.sh

/usr/bin/expect
set timeout 20
set userName [lindex $argv 0]

spawn telnet localhost

expect "Login: "
send "$userName\r"
interact

/etc/mgetty/login.config

*       -       -       /sbbs/getty.sh @

/etc/mgetty/mgetty.config

debug 4

fax-id

speed 38400

issue-file /etc/issue.mgetty

port ttyACM0

 debug 8

 init-chat "" AT OK

/etc/issue.mgetty

anyBBS Dialup to Telnet Launcher v0.1 on \P at \S (\I)

Enter User Name or Number or 'New'

/etc/systemd/system/getty.target.wants/getty@ttyACM0.service

[Unit]
Description=Getty on %I
Documentation=man:agetty(8) man:systemd-getty-generator(8)
Documentation=http://0pointer.de/blog/projects/serial-console.html
After=systemd-user-sessions.service plymouth-quit-wait.service
After=rc-local.service

Before=getty.target

IgnoreOnIsolate=yes
ConditionPathExists=/dev/tty0

[Service]
ExecStart=-/sbin/mgetty -n 2 ttyACM0
Type=idle
Restart=always
RestartSec=0
UtmpIdentifier=%I
TTYPath=/dev/%I
TTYReset=yes
TTYVHangup=yes
TTYVTDisallocate=yes
KillMode=process
IgnoreSIGPIPE=no
SendSIGHUP=yes

Environment=LANG= LANGUAGE= LC_CTYPE= LC_NUMERIC= LC_TIME= LC_COLLATE= LC_MONETARY= LC_MESSAGES= LC_PAPER= LC_NAME= LC_ADDRESS= LC_TELEPHONE= LC_MEASUREMENT= LC_IDENTIFICATION=

[Install]
WantedBy=getty.target
DefaultInstance=ttyACM0

SainSmart 3.5 inch TFT LCD 320*480 Touch Screen Display for Raspberry Pi 2 B+/B DE Lager

Key Parameters

LCD Type	TFT
LCD Interface	SPI
Touch Screen Type	Resistive
Touch Screen Controller	XPT2046
Colors	65536
Backlight	LED
Resolution	320*480 (Pixel)
Aspect Ratio	2:03
Power Consumption	TBD
Backlight Current	TBD
Operating Temp. (℃)	TBD

Interface

PIN NO.	SYMBOL	DESCRIPTION
1, 17	3.3V	Power positive (3.3V power input)
2, 4	5V	Power positive (5V power input)
3, 5, 7, 8, 10, 12, 13, 15, 16	NC	NC
6, 9, 14, 20, 25	GND	Ground
11	TP_IRQ	Touch Panel interrupt, low level while the Touch Panel detects touching
18	LCD_RS	Instruction/Data Register selection
19	LCD_SI / TP_SI	SPI data input of LCD/Touch Panel
21	TP_SO	SPI data output of Touch Panel
22	RST	Reset
23	LCD_SCK / TP_SCK	SPI clock of LCD/Touch Panel
24	LCD_CS	LCD chip selection, low active
26	TP_CS	Touch Panel chip selection, low active

Here are the key values, i have not tested on the current distro, these came from the rpi2 image at sainsmart for this display.

/etc/modules

i2c-bcm2708
i2c-dev

flexfb  width=320  height=480  regwidth=16 init=-1,0xb0,0x0,-1,0x11,-2,250,-1,0x3A,0x55,-1,0xC2,0x44,-1,0xC5,0x00,0x00,0x00,0x00,-1,0xE0,0x0F,0x1F,0x1C,0x0C,0x0F,0x08,0x48,0x98,0x37,0x0A,0x13,0x04,0x11,0x0D,0x00,-1,0xE1,0x0F,0x32,0x2E,0x0B,0x0D,0x05,0x47,0x75,0x37,0x06,0x10,0x03,0x24,0x20,0x00,-1,0xE2,0x0F,0x32,0x2E,0x0B,0x0D,0x05,0x47,0x75,0x37,0x06,0x10,0x03,0x24,0x20,0x00,-1,0x36,0x28,-1,0x11,-1,0x29,-3
fbtft_device debug=3 rotate=90 name=flexfb speed=16000000 gpios=reset:25,dc:24
ads7846_device model=7846 cs=1 gpio_pendown=17  keep_vref_on=1 swap_xy=1 pressure_max=255 x_plate_ohms=60 x_min=200 x_max=3900 y_min=200 y_max=3900

/boot/cmdline.txt

dwc_otg.lpm_enable=0 console=tty1 console=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo